4.7:Copter_trim

x

common/source/docs/common-auxiliary-functions.rst

@@ -296,6 +296,8 @@ Supported Features
 +----------------------+----------------------------+----------+---------+---------+
 |        181           | VTOL QuickTune             |          |    X    |         |
 +----------------------+----------------------------+----------+---------+---------+
+|        182           | InFlight AHRS trim adjust  |    X     |         |         |
++----------------------+----------------------------+----------+---------+---------+
 
 
 Intended as continuous PWM range control inputs:
@@ -594,6 +596,7 @@ Other functions are:
     ICEngine start / stop                 Controls ICE engine starter output :ref:`ICE engines<common-ice>`
     Autotune_test_gains                   After autotune,allows selecting tune(high) or pretune gains
     VTOL QuickTune                        Autotunes QuadPlane VTOL PIDs, see :ref:`quicktune`
+    InFlight AHRS trim adjust             Auto Trim for Copter, see :ref:`autotrim`
     ROLL Input                            ROLL input channel. (replaces RCMAP)
     PITCH Input                           PITCH input channel. (replaces RCMAP)
     THROTTLE Input                        THROTTLE input channel. (replaces RCMAP)

copter/source/docs/autotrim.rst

@@ -10,10 +10,10 @@ Wind of course has a strong effect on your copter and will push it around. Howev
 
     For most users this procedure is not necessary because the :ref:`accelerometer calibration <common-accelerometer-calibration>` does a good job of setting the trim values.
 
-Save Trim
+Auto Trim
 ~~~~~~~~~
 
-Save trim is the simpler method and involves essentially transferring your radio transmitter's trims to the autopilot (`video demo here <https://www.youtube.com/watch?v=ayA0uYOqKX4>`__).
+With Auto Trim the roll and pitch corrections are captured as you fly in a stable hover. Setup a :ref:`common-auxiliary-functions` switch to "In Flight AHRS trim adjust" ("182").
 
 1. Check that your CH7 switch goes above 1800 on the MissionPlanner's Hardware > Mandatory Hardware > Radio Calibration screen
 
@@ -25,54 +25,49 @@ Save trim is the simpler method and involves essentially transferring your radio
 .. image:: ../images/MP_SaveTrim_Ch7.png
     :target: ../_images/MP_SaveTrim_Ch7.png
 
-3. With your CH7 switch in the off position, fly your copter in Stabilize mode and use your transmitters's roll and pitch trim to get it flying level
+3. Find a wind free environment with sufficient space to fly your copter without crashing into something
 
-4. Land and put your throttle to zero
+4. Put the vehicle in Stabilize mode
 
-5. Release the roll and pitch sticks and switch the CH7 switch high for at least 1 second.  The words "Trim saved" should appear in the MP's Flight Data screen's Messages tab
+5. Arm the vehicle and lift into a hover. Flip the switch that you setup to  its high position (>1800us).
 
-6. Reset your transmitters roll and pitch trims back to the center and fly again and it should fly level now. If it does not repeat steps 3, 4 & 5
+6. Fly your copter for about 25 seconds in a stable hover in position, keeping it from drifting with the pitch and roll sticks. As the trim is adjusted, less and less corrections with the sticks will be required.
 
-Auto Trim
-~~~~~~~~~
+7. Once satisfied, flip the switch low, saving the trims, and land.
 
-With auto trim the roll and pitch trim are captured as you fly in a stable hover.
+8. Take off again in stabilize mode and check if your copter is flying level now. If not repeat steps 4 - 7 again.
 
-1. Find a wind free environment with sufficient space to fly your copter without crashing into something
-
-2. Put the vehicle in Stabilize mode
-
-3. Hold throttle down and rudder right for 15seconds or until you see the small red, blue and yellow leds flash in a cyclic pattern
+.. note::
 
-4. Fly your copter for about 25 seconds in a stable hover
+     You can manually set the trim by modifying the :ref:`AHRS_TRIM_X <AHRS_TRIM_X>` and :ref:`AHRS_TRIM_Y <AHRS_TRIM_Y>`. Roll trim is :ref:`AHRS_TRIM_X <AHRS_TRIM_X>`, Pitch trim is :ref:`AHRS_TRIM_Y <AHRS_TRIM_Y>`. Both values are in radians with left roll and forward pitch being negative numbers.
 
-5. Land and put your throttle to zero and wait for a few seconds (the trims parameters are being saved)
+.. note::
 
-6. Take off again in stabilize mode and check if your copter is flying level now. If not repeat steps 2, 3 and 4
+    It is nearly impossible to get rid of all drift so that your copter remains completely motionless without any input.
 
-.. note::
+Save Trim
+~~~~~~~~~
+.. note:: the above AUTO TRIM method is preferred since it does not involve moving transmitter trims after RC calibration.
 
-    You can also test these procedures above are operational on the ground with your battery disconnected. Connect your autopilot to the mission planner and observing the Flight Data screen as you simulate completing the steps above.
+Save trim involves essentially transferring your radio transmitter's trims to correct the autopilot's accelerometer trim. Normally, once :ref:`common-accelerometer-calibration` is done, you never want to change the transmitter's trims, but in this case it is done **temporarily**. The "Save Trim" function ("5") is assigned to any free RC channel, usually a switch based one, using an :ref:`common-auxiliary-functions`. For the example below, Channel 7 will be used.
 
-.. image:: ../images/MP_SaveTrim_FlightDataScreen.jpg
-    :target: ../_images/MP_SaveTrim_FlightDataScreen.jpg
+1. Check that your CH7 switch goes above 1800 on the MissionPlanner's Hardware > Mandatory Hardware > Radio Calibration screen
 
-.. note::
+.. image:: ../images/MP_SaveTrim_Ch7PWMCheck.png
+    :target: ../_images/MP_SaveTrim_Ch7PWMCheck.png
 
-    You can manually set the trim by modifying the :ref:`AHRS_TRIM_X <AHRS_TRIM_X>` and :ref:`AHRS_TRIM_Y <AHRS_TRIM_Y>`. Roll trim is :ref:`AHRS_TRIM_X <AHRS_TRIM_X>`, Pitch trim is :ref:`AHRS_TRIM_Y <AHRS_TRIM_Y>`. Both values are in radians with left roll and forward pitch being negative numbers.
+2. Set the CH7 Option to Save Trim on the Software > Copter Pids screen and press the "Write Params" button
 
-.. note::
+.. image:: ../images/MP_SaveTrim_Ch7.png
+    :target: ../_images/MP_SaveTrim_Ch7.png
 
-    It is nearly impossible to get rid of all drift so that your copter remains completely motionless without any input.
+3. With your CH7 switch in the off position, fly your copter in Stabilize mode and use your transmitters's roll and pitch trim to get it flying level
 
-Video demonstrations of Save Trim and Auto Trim
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+4. Land and put your throttle to zero
 
-..  youtube:: 5z0zuwicZh8
-    :width: 100%
+5. Release the roll and pitch sticks and switch the CH7 switch high for at least 1 second.  The words "Trim saved" should appear in the MP's Flight Data screen's Messages tab
 
-..  youtube:: e3OF9ih50PU
-    :width: 100%
+6. Reset your transmitters roll and pitch trims back to the center and fly again and it should fly level now. If it does not repeat steps 3, 4 & 5
 
 Desktop method
 ~~~~~~~~~~~~~~
@@ -88,7 +83,7 @@ lower "Calibrate Level" button.
 Please note though that making the HUD level while the vehicle is on the
 ground does not necessarily mean it won't drift horizontally while
 flying because of other small frame issues including the flight
-controller not being perfectly level on the frame and slightly tilted
+controller not being perfectly level on the frame, CG placement, an/ord slightly tilted
 motors.
 
 .. |MP_SaveTrim_Ch7| image:: ../images/MP_SaveTrim_Ch7.png