heatpump.yaml

substitutions:
  devicename: heatpump
  description: Heatpump Controller
  entity_prefix: Heatpump

globals:
  - id: unmasked_value_water_temperature_t1s
    type: int
    restore_value: no
    initial_value: '0'
  - id: unmasked_curve_selection
    type: int
    restore_value: no
    initial_value: '0'

esphome:
  name: "${devicename}"
  comment: "${description}"
  friendly_name: "${description}"

esp32:
  board: esp32dev
  framework:
    type: arduino

# Enable logging
logger:
  level: INFO
  baud_rate: 0

# Enable Home Assistant API
api:

web_server:
  port: 80

ota:

wifi:
  power_save_mode: none
  ssid: !secret wifi_ssid
  password: !secret wifi_password

  # Enable fallback hotspot (captive portal) in case wifi connection fails
  ap:
    ssid: "${devicename}-setup"
    password: "heatpump"

captive_portal:

uart:
  id: mod_bus
  tx_pin: 17
  rx_pin: 16
  baud_rate: 9600
  stop_bits: 1

modbus:
  flow_control_pin: 5
  id: heatpump_modbus

modbus_controller:
  - id: "${devicename}"
    ## the Modbus device addr
    address: 0x1
    modbus_id: heatpump_modbus
    setup_priority: -10
    update_interval: 10s

sensor:
  - platform: uptime
    name: "${entity_prefix} Uptime"
  # Register: 1
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Operational Mode"
    id: "${devicename}_operational_mode"
    register_type: holding
    address: 0x1
    value_type: U_WORD
  # Register: 2 -> Is present in this config as a 'number'
  # Register: 3
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Air Temperature Ts"
    id: "${devicename}_air_temperature_ts"
    register_type: holding
    address: 0x3
    value_type: U_WORD
    unit_of_measurement: "°C"
    filters:
      - multiply: 0.5
  # Register: 4
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} DHW Tank Temperature T5s"
    id: "${devicename}_dhw_tank_temperature_t5s"
    register_type: holding
    address: 0x4
    value_type: S_WORD
    unit_of_measurement: "°C"
  # Register: 6 -> Is present in this config as a 'number'
  # Register: 7
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Forced Water Tank Heating"
    id: "${devicename}_forced_water_tank_heating"
    register_type: holding
    address: 0x7
    value_type: U_WORD
  # Register: 8
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Forced Tank Backup Heater"
    id: "${devicename}_forced_tbh"
    register_type: holding
    address: 0x8
    value_type: U_WORD
  # Register: 9
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Forced Hydraulic Module Rear Electric Heater 1"
    id: "${devicename}_forced_hydraulic_module_rear_electric_heater_1"
    register_type: holding
    address: 0x9
    value_type: U_WORD
  # Register: 10
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} t_SG_MAX"
    id: "${devicename}_t_sg_max"
    register_type: holding
    address: 0xa
    value_type: U_WORD
    unit_of_measurement: hr

  # Register: 100
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Compressor Operating Frequency"
    id: "${devicename}_compressor_operating_frequency"
    register_type: holding
    address: 0x64
    value_type: U_WORD
    unit_of_measurement: Hz
  # Register: 101
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Operating Mode"
    id: "${devicename}_operating_mode"
    register_type: holding
    address: 0x65
    value_type: U_WORD
  # Register: 102
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Fan Speed"
    id: "${devicename}_fan_speed"
    register_type: holding
    address: 0x66
    unit_of_measurement: "r/min"
    value_type: U_WORD
    icon: mdi:fan
  # Register: 103
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} PMV Openness"
    id: "${devicename}_pmv_openness"
    register_type: holding
    address: 0x67
    value_type: U_WORD
    unit_of_measurement: "Pa"
  # Register: 104
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Water Inlet Temperature"
    id: "${devicename}_water_inlet_temperature"
    register_type: holding
    address: 0x68
    value_type: S_WORD
    unit_of_measurement: "°C"
  # Register: 105
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Water Outlet Temperature"
    id: "${devicename}_water_outlet_temperature"
    register_type: holding
    address: 0x69
    value_type: S_WORD
    unit_of_measurement: "°C"
  # Register: 106
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Condensor Temperature T3"
    id: "${devicename}_condensor_temperature_t3"
    register_type: holding
    address: 0x6a
    value_type: S_WORD
    unit_of_measurement: "°C"
  # Register: 107
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Outdoor Ambient Temperature"
    id: "${devicename}_outdoor_ambient_temperature"
    register_type: holding
    address: 0x6B
    unit_of_measurement: "°C"
    value_type: S_WORD
  # Register: 108
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Discharge Temperature"
    id: "${devicename}_discharge_temperature"
    register_type: holding
    address: 0x6c
    value_type: S_WORD
    unit_of_measurement: "°C"
  # Register: 109
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Return Air Temperature"
    id: "${devicename}_return_air_temperature"
    register_type: holding
    address: 0x6d
    value_type: S_WORD
    unit_of_measurement: "°C"
  # Register: 110
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Total Water Outlet Temperature T1"
    id: "${devicename}_total_water_outlet_temperature_t1"
    register_type: holding
    address: 0x6e
    value_type: S_WORD
    unit_of_measurement: "°C"
  # Register: 111
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} System Total Water Outlet Temperature T1B"
    id: "${devicename}_system_total_water_outlet_temperature_t1b"
    register_type: holding
    address: 0x6f
    value_type: S_WORD
    unit_of_measurement: "°C"
  # Register: 112
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Refrigerant Liquid Side Temperature T2"
    id: "${devicename}_refrigerant_liquid_side_temperature_t2"
    register_type: holding
    address: 0x70
    value_type: S_WORD
    unit_of_measurement: "°C"
  # Register: 113
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Refrigerant Gas Side Temperature T2B"
    id: "${devicename}_refrigerant_gas_side_temperature_t2b"
    register_type: holding
    address: 0x71
    value_type: S_WORD
    unit_of_measurement: "°C"
  # Register: 114
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Room Temperature Ta"
    id: "${devicename}_room_temperature_ta"
    register_type: holding
    address: 0x72
    value_type: S_WORD
    unit_of_measurement: "°C"
  # Register: 115
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Water Tank Temperature T5"
    id: "${devicename}_water_tank_temperature_t5"
    register_type: holding
    address: 0x73
    unit_of_measurement: "°C"
    value_type: S_WORD
    icon: mdi:thermometer-water
  # Register: 116
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Outdoor Unit High Pressure"
    id: "${devicename}_outdoor_unit_high_pressure"
    register_type: holding
    address: 0x74
    value_type: U_WORD
    unit_of_measurement: kPA
  # Register: 117
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix}  Outdoor Unit Low Pressure"
    id: "${devicename}_outdoor_unit_low_pressure"
    register_type: holding
    address: 0x75
    value_type: U_WORD
    unit_of_measurement: kPA
  # Register: 118
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Outdoor Unit Current"
    id: "${devicename}_outdoor_unit_current"
    register_type: holding
    address: 0x76
    value_type: U_WORD
    unit_of_measurement: A
  # Register: 119
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Outdoor Unit Voltage"
    id: "${devicename}_outdoor_unit_voltage"
    register_type: holding
    address: 0x77
    value_type: U_WORD
    unit_of_measurement: V
  # Register: 120
  # Midea: Tbt1
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Hydraulic Module Current 1"
    id: "${devicename}_hydraulic_module_current_1"
    register_type: holding
    address: 0x78
    value_type: U_WORD
  # Register: 121
  # Midea: Tbt2
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Hydraulic Module Current 2"
    id: "${devicename}_hydraulic_module_current_2"
    register_type: holding
    address: 0x79
    value_type: U_WORD
  # Register: 122
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Compressor Operation Time"
    id: "${devicename}_compressor_operation_time"
    register_type: holding
    address: 0x7a
    value_type: U_WORD
    unit_of_measurement: hr
  # Register: 123
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Unit Capacity"
    id: "${devicename}_unit_capacity"
    register_type: holding
    address: 0x7b
    value_type: U_WORD
  # Register: 124
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Current Fault"
    id: "${devicename}_current_fault"
    register_type: holding
    entity_category: diagnostic
    address: 0x7c
    value_type: U_WORD
  # Register: 125
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Fault 1"
    id: "${devicename}_fault_1"
    register_type: holding
    entity_category: diagnostic
    address: 0x7d
    value_type: U_WORD
  # Register: 126
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Fault 2"
    id: "${devicename}_fault_2"
    register_type: holding
    entity_category: diagnostic
    address: 0x7e
    value_type: U_WORD
  # Register: 127
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Fault 3"
    id: "${devicename}_fault_3"
    register_type: holding
    entity_category: diagnostic
    address: 0x7f
    value_type: U_WORD
  # Register: 130
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Software Version"
    id: "${devicename}_software_version"
    register_type: holding
    address: 0x82
    value_type: U_WORD
  # Register: 131
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Wired Controller Version Number"
    id: "${devicename}_wired_controller_version_number"
    register_type: holding
    address: 0x83
    value_type: U_WORD
  # Register: 132
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Compressor Target Frequency"
    id: "${devicename}_compressor_target_frequency"
    register_type: holding
    address: 0x84
    value_type: U_WORD
    unit_of_measurement: Hz
  # Register: 133
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} DC Bus Current"
    id: "${devicename}_dc_bus_current"
    register_type: holding
    address: 0x85
    value_type: U_WORD
    unit_of_measurement: A
  # Register: 134
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} DC Bus Voltage"
    id: "${devicename}_dc_bus_voltage"
    register_type: holding
    address: 0x86
    value_type: U_WORD
    unit_of_measurement: V
    filters:
      - multiply: 10
  # Register: 135
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} TF module temperature"
    id: "${devicename}_tf_module_temperature"
    register_type: holding
    address: 0x87
    unit_of_measurement: "°C"
    value_type: S_WORD
  # Register: 136
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Climate Curve T1S Calculated Value 1"
    id: "${devicename}_climate_curve_t1s_calculated_value_1"
    register_type: holding
    address: 0x88
    value_type: S_WORD
    unit_of_measurement: "°C"
  # Register: 137
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Climate Curve T1S Calculated Value 2"
    id: "${devicename}_climate_curve_t1s_calculated_value_2"
    register_type: holding
    address: 0x89
    value_type: S_WORD
    unit_of_measurement: "°C"
  # Register: 138
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Water Flow"
    id: "${devicename}_water_flow"
    register_type: holding
    address: 0x8a
    value_type: U_WORD
    unit_of_measurement: m3/H
    accuracy_decimals: 2
    filters:
      - lambda: return x * 0.01;
  # Register: 139
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Limit Scheme Of Outdoor Unit Current"
    id: "${devicename}_limit_scheme_of_outdoor_unit_current"
    register_type: holding
    address: 0x8b
    value_type: U_WORD
  # Register: 140
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Ability Of Hydraulic Module"
    id: "${devicename}_ability_of_hydraulic_module"
    register_type: holding
    address: 0x8c
    value_type: U_WORD
    unit_of_measurement: kW
    accuracy_decimals: 2
    filters:
      - lambda: return x * 0.01;
  # Register: 141
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Tsolar"
    id: "${devicename}_tsolar"
    register_type: holding
    address: 0x8d
    value_type: U_WORD
  # Register: 143 and 144
  # U_DWORD combines this register with the next one
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Electricity Consumption"
    id: "${devicename}_electricity_consumption"
    register_type: holding
    unit_of_measurement: "kWh"
    state_class: total_increasing
    address: 0x8f
    value_type: U_DWORD
  # Register: 145 and 146
  # U_DWORD combines this register with the next one
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Power Output"
    id: "${devicename}_power_output"
    register_type: holding
    unit_of_measurement: "kWh"
    state_class: total_increasing
    address: 0x91
    value_type: U_DWORD

  # Register: 200 (High byte)
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Home Appliance Type"
    id: "${devicename}_home_appliance_type"
    register_type: holding
    address: 0xc8
    value_type: U_WORD
    bitmask: 0x00FF
  # Register: 200 (Low byte, first 4 bits)
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Home Appliance Sub Type"
    id: "${devicename}_home_appliance_sub_type"
    register_type: holding
    address: 0xc8
    value_type: U_WORD
    bitmask: 0xF000
  # Register: 200 (Low byte, second 4 bits)
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Home Appliance Product Code"
    id: "${devicename}_home_appliance_product_code"
    register_type: holding
    address: 0xc8
    value_type: U_WORD
    bitmask: 0x0F00
  # Register: 201 (Low), default: 25, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Temperature Upper Limit Of T1S Cooling Zone 1"
    id: "${devicename}_temperature_upper_limit_of_t1s_cooling_zone_1"
    register_type: holding
    address: 0xc9
    value_type: S_WORD
    unit_of_measurement: "°C"
    bitmask: 0x00FF
  # Register: 201 (High), default: 25, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Temperature Upper Limit Of T1S Cooling Zone 2"
    id: "${devicename}_temperature_upper_limit_of_t1s_cooling_zone_2"
    register_type: holding
    address: 0xc9
    value_type: S_WORD
    unit_of_measurement: "°C"
    bitmask: 0xFF00
  # Register: 202 (Low), default: 5, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Temperature Lower Limit Of T1S Cooling Zone 1"
    id: "${devicename}_temperature_lower_limit_of_t1s_cooling_zone_1"
    register_type: holding
    address: 0xca
    value_type: S_WORD
    unit_of_measurement: "°C"
    bitmask: 0x00FF
  # Register: 202 (High), default: 5, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Temperature Lower Limit Of T1S Cooling Zone 2"
    id: "${devicename}_temperature_lower_limit_of_t1s_cooling_zone_2"
    register_type: holding
    address: 0xca
    value_type: S_WORD
    unit_of_measurement: "°C"
    bitmask: 0xFF00
  # Register: 203 (Low), default: 55, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Temperature Upper Limit Of T1S Heating Zone 1"
    id: "${devicename}_temperature_upper_limit_of_t1s_heating_zone_1"
    register_type: holding
    address: 0xcb
    value_type: S_WORD
    unit_of_measurement: "°C"
    bitmask: 0x00FF
  # Register: 203 (High), default: 55, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Temperature Upper Limit Of T1S Heating Zone 2"
    id: "${devicename}_temperature_upper_limit_of_t1s_heating_zone_2"
    register_type: holding
    address: 0xcb
    value_type: S_WORD
    unit_of_measurement: "°C"
    bitmask: 0xFF00
  # Register: 204 (Low), default: 25, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Temperature Lower Limit Of T1S Heating Zone 1"
    id: "${devicename}_temperature_lower_limit_of_t1s_heating_zone_1"
    register_type: holding
    address: 0xcc
    value_type: S_WORD
    unit_of_measurement: "°C"
    bitmask: 0x00FF
  # Register: 204 (High), default: 25, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Temperature Lower Limit Of T1S Heating Zone 2"
    id: "${devicename}_temperature_lower_limit_of_t1s_heating_zone_2"
    register_type: holding
    address: 0xcc
    value_type: S_WORD
    unit_of_measurement: "°C"
    bitmask: 0xFF00
  # Register: 205 -> Is present in this config as a 'number'
  # Register: 206 -> Is present in this config as a 'number'
  # Register: 207 -> Is present in this config as a 'number'
  # Register: 208 -> Is present in this config as a 'number'
  # Register: 209 -> Is present in this config as a 'number'
  # Register: 212 -> Is present in this config as a 'number'
  # Register: 213 -> Is present in this config as a 'number'
  # Register: 214 -> Is present in this config as a 'number'
  # Register: 215 -> Is present in this config as a 'number'
  # Register: 216 -> Is present in this config as a 'number'
  # Register: 217 -> Is present in this config as a 'number'
  # Register: 218 -> Is present in this config as a 'number'
  # Register: 219 -> Is present in this config as a 'number'
  # Register: 220 -> Is present in this config as a 'number'
  # Register: 221 -> Is present in this config as a 'number'
  # Register: 222 -> Is present in this config as a 'number'
  # Register: 223 -> Is present in this config as a 'number'
  # Register: 224 -> Is present in this config as a 'number'
  # Register: 225 -> Is present in this config as a 'number'
  # Register: 226 -> Is present in this config as a 'number'
  # Register: 227 -> Is present in this config as a 'number'
  # Register: 228 -> Is present in this config as a 'number'
  # Register: 229 -> Is present in this config as a 'number'
  # Register: 230 -> Is present in this config as a 'number'
  # Register: 231 -> Is present in this config as a 'number'
  # Register: 232 -> Is present in this config as a 'number'
  # Register: 233 -> Is present in this config as a 'number'
  # Register: 234 -> Is present in this config as a 'number'
  # Register: 235 -> Is present in this config as a 'number'
  # Register: 237 -> Is present in this config as a 'number'
  # Register: 238 -> Is present in this config as a 'number'
  # Register: 240 -> Is present in this config as a 'number'
  # Register: 241 -> Is present in this config as a 'number'
  # Register: 242 -> Is present in this config as a 'number'
  # Register: 243 -> Is present in this config as a 'number'
  # Register: 244 -> Is present in this config as a 'number'
  # Register: 245 -> Is present in this config as a 'number'
  # Register: 246 -> Is present in this config as a 'number'
  # Register: 247 -> Is present in this config as a 'number'
  # Register: 248 -> Is present in this config as a 'number'
  # Register: 249 -> Is present in this config as a 'number'
  # Register: 250 -> Is present in this config as a 'number'
  # Register: 251 -> Is present in this config as a 'number'
  # Register: 252 -> Is present in this config as a 'number'
  # Register: 253
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Comfort Parameter Reserved 3"
    id: "${devicename}_comfort_parameter_3"
    register_type: holding
    address: 0xfd
    value_type: U_WORD
  # Register: 254
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Comfort Parameter Reserved 4"
    id: "${devicename}_comfort_parameter_4"
    register_type: holding
    address: 0xfe
    value_type: U_WORD
  # Register: 255 -> Is present in this config as a 'number'
  # Register: 256 -> Is present in this config as a 'number'
  # Register: 257 -> Is present in this config as a 'number'
  # Register: 258 -> Is present in this config as a 'number'
  # Register: 259 -> Is present in this config as a 'number'
  # Register: 260 -> Is present in this config as a 'number'
  # Register: 261 -> Is present in this config as a 'number'
  # Register: 262 -> Is present in this config as a 'number'
  # Register: 263 -> Is present in this config as a 'number'
  # Register: 264 -> Is present in this config as a 'number'
  # Register: 265 -> Is present in this config as a 'number'
  # Register: 266 -> Is present in this config as a 'number'
  # Register: 267 -> Is present in this config as a 'number'
  # Register: 268 -> Is present in this config as a 'number'
  # Register: 269, default: 0
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Power Input Limitation Type"
    id: "${devicename}_power_input_limitation_type"
    register_type: holding
    address: 0x10d
    value_type: U_WORD
  # Register: 270 (Low), default: 0.5, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} t_T4 FRESH_H"
    id: "${devicename}_t_t4_fresh_h"
    register_type: holding
    address: 0x10e
    value_type: U_WORD
    unit_of_measurement: hr
    accuracy_decimals: 1
    bitmask: 0x00FF
    filters:
      - multiply: 0.5
  # Register: 270 (High), default: 0.5, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} t_T4 FRESH_C"
    id: "${devicename}_t_t4_fresh_c"
    register_type: holding
    address: 0x10e
    value_type: U_WORD
    unit_of_measurement: hr
    accuracy_decimals: 1
    bitmask: 0xFF00
    filters:
      - multiply: 0.5
  # Register: 271, default: 2, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Built-in Circulating Pump Delay"
    id: "${devicename}_t_pumpi_delay"
    register_type: holding
    address: 0x10f
    value_type: U_WORD
    unit_of_measurement: hr
    filters:
      - multiply: 0.5
  # Register: 272 (Low, first 4 bits), default: 0, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Zone 1 End Heating Mode Emission Type"
    id: "${devicename}_zone_1_end_heating_mod_emission_type"
    register_type: holding
    address: 0x110
    value_type: U_WORD
    bitmask: 0xF000
  # Register: 272 (Low, second 4 bits), default: 0, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Zone 2 End Heating Mode Emission Type"
    id: "${devicename}_zone_2_end_heating_mod_emission_type"
    register_type: holding
    address: 0x110
    value_type: U_WORD
    bitmask: 0x0F00
  # Register: 272 (High, first 4 bits), default: 2, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Zone 1 End Cooling Mode Emission Type"
    id: "${devicename}_zone_1_end_cooling_mod_emission_type"
    register_type: holding
    address: 0x110
    value_type: U_WORD
    bitmask: 0x00F0
  # Register: 272 (High, second 4 bits), default: 2, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Zone 2 End Cooling Mode Emission Type"
    id: "${devicename}_zone_2_end_cooling_mod_emission_type"
    register_type: holding
    address: 0x110
    value_type: U_WORD
    bitmask: 0x000F

binary_sensor:
  # Register: 0
  # Bit: 0
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Power Floor Heating Zone 1"
    id: "${devicename}_power_floor_heating_zone_1"
    register_type: holding
    address: 0x0
    bitmask: 0x1
  # Bit: 1
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Power Air Conditioner Zone 1"
    id: "${devicename}_power_air_conditioner_zone_1"
    register_type: holding
    address: 0x0
    bitmask: 0x2
  # Bit: 2 -> Is present in this config as a 'switch'
  # Bit: 3
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Power Air Conditioner Zone 2"
    id: "${devicename}_power_air_conditioner_zone_2"
    register_type: holding
    address: 0x0
    bitmask: 0x8
  # Bit: 4
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Power Reserved BIT 4"
    id: "${devicename}_power_reserved_bit_4"
    register_type: holding
    address: 0x0
    bitmask: 0x10
  # Bit: 5
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Power Reserved BIT 5"
    id: "${devicename}_power_reserved_bit_5"
    register_type: holding
    address: 0x0
    bitmask: 0x20
  # Bit: 6
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Power Reserved BIT 6"
    id: "${devicename}_power_reserved_bit_6"
    register_type: holding
    address: 0x0
    bitmask: 0x40
  # Bit: 7
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Power Reserved BIT 7"
    id: "${devicename}_power_reserved_bit_7"
    register_type: holding
    address: 0x0
    bitmask: 0x80
  # Bit: 8
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Power Reserved BIT 8"
    id: "${devicename}_power_reserved_bit_8"
    register_type: holding
    address: 0x0
    bitmask: 0x100
  # Bit: 9
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Power Reserved BIT 9"
    id: "${devicename}_power_reserved_bit_9"
    register_type: holding
    address: 0x0
    bitmask: 0x200
  # Bit: 10
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Power Reserved BIT 10"
    id: "${devicename}_power_reserved_bit_10"
    register_type: holding
    address: 0x0
    bitmask: 0x400
  # Bit: 11
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Power Reserved BIT 11"
    id: "${devicename}_power_reserved_bit_11"
    register_type: holding
    address: 0x0
    bitmask: 0x800
  # Bit: 12
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Power Reserved BIT 12"
    id: "${devicename}_power_reserved_bit_12"
    register_type: holding
    address: 0x0
    bitmask: 0x1000
  # Bit: 13
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Power Reserved BIT 13"
    id: "${devicename}_power_reserved_bit_13"
    register_type: holding
    address: 0x0
    bitmask: 0x2000
  # Bit: 14
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Power Reserved BIT 14"
    id: "${devicename}_power_reserved_bit_14"
    register_type: holding
    address: 0x0
    bitmask: 0x4000
  # Bit: 15
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Power Reserved BIT 15"
    id: "${devicename}_power_reserved_bit_15"
    register_type: holding
    address: 0x0
    bitmask: 0x8000

  # Register: 5
  # Bit: 0
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Function Setting Reserved BIT 0"
    id: "${devicename}_function_setting_reserved_bit_0"
    register_type: holding
    address: 0x5
    bitmask: 0x1
  # Bit: 1
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Function Setting Reserved BIT 1"
    id: "${devicename}_function_setting_reserved_bit_1"
    register_type: holding
    address: 0x5
    bitmask: 0x2
  # Bit: 2
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Function Setting Reserved BIT 2"
    id: "${devicename}_function_setting_reserved_bit_2"
    register_type: holding
    address: 0x5
    bitmask: 0x4
  # Bit: 3
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Function Setting Reserved BIT 3"
    id: "${devicename}_function_setting_reserved_bit_3"
    register_type: holding
    address: 0x5
    bitmask: 0x8
  # Bit: 4
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Function Setting Disinfect"
    id: "${devicename}_function_setting_disinfect"
    register_type: holding
    address: 0x5
    bitmask: 0x10
  # Bit: 5
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Function Setting Holiday Away"
    id: "${devicename}_function_setting_holiday_away"
    register_type: holding
    address: 0x5
    bitmask: 0x20
  # Bit: 6
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Function Setting Silent Mode"
    id: "${devicename}_function_setting_silent_mode"
    register_type: holding
    address: 0x5
    bitmask: 0x40
  # Bit: 7
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Function Setting Silent Mode Level"
    id: "${devicename}_function_setting_silent_mode_level"
    register_type: holding
    address: 0x5
    bitmask: 0x80
  # Bit: 8
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Function Setting Holiday Home"
    id: "${devicename}_function_setting_holiday_home"
    register_type: holding
    address: 0x5
    bitmask: 0x100
  # Bit: 9
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Function Setting Reserved BIT 9"
    id: "${devicename}_function_setting_reserved_bit_9"
    register_type: holding
    address: 0x5
    bitmask: 0x200
  # Bit: 10
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Function Setting ECO Mode"
    id: "${devicename}_function_setting_eco_mode"
    register_type: holding
    address: 0x5
    bitmask: 0x400
  # Bit: 11
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Function Setting DHW Pumps Running Constant Temperature Water Recycling"
    id: "${devicename}_function_setting_dhw_pumps_running_constant_temperature_water_recycling"
    register_type: holding
    address: 0x5
    bitmask: 0x800
  # Bit: 12 -> Is present in this config as a 'switch'
  # Bit: 13 -> Is present in this config as a 'switch'
  # Bit: 14
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Function Setting Reserved BIT 14"
    id: "${devicename}_function_setting_reserved_bit_14"
    register_type: holding
    address: 0x5
    bitmask: 0x4000
  # Bit: 15
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Function Setting Reserved BIT 15"
    id: "${devicename}_function_setting_reserved_bit_15"
    register_type: holding
    address: 0x5
    bitmask: 0x8000

  # Register: 128
  # Bit: 0
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Status BIT 1 Reserved BIT 0"
    id: "${devicename}_status_bit_1_reserved_bit_0"
    register_type: holding
    address: 0x80
    bitmask: 0x1
  # Bit: 1
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Status BIT 1 Defrosting"
    id: "${devicename}_status_bit_1_defrosting"
    register_type: holding
    address: 0x80
    bitmask: 0x2
  # Bit: 2
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Status BIT 1 Anti Freezing"
    id: "${devicename}_status_bit_1_anti_freezing"
    register_type: holding
    address: 0x80
    bitmask: 0x4
  # Bit: 3
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Status BIT 1 Oil Return"
    id: "${devicename}_status_bit_1_oil_return"
    register_type: holding
    address: 0x80
    bitmask: 0x8
  # Bit: 4
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Status BIT 1 Remote On/Off"
    id: "${devicename}_status_bit_1_remote_on_off"
    register_type: holding
    address: 0x80
    bitmask: 0x10
  # Bit: 5
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Status BIT 1 Outdoor Unit Test Mode Mark"
    id: "${devicename}_status_bit_1_outdoor_unit_test_mode_mark"
    register_type: holding
    address: 0x80
    bitmask: 0x20
  # Bit: 6
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Status BIT 1 Heating Mode Set By Room Thermostat"
    id: "${devicename}_status_bit_1_heating_mode_set_by_room_thermostat"
    register_type: holding
    address: 0x80
    bitmask: 0x40
  # Bit: 7
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Status BIT 1 Cooling Mode Set By Room Thermostat"
    id: "${devicename}_status_bit_1_cooling_mode_set_by_room_thermostat"
    register_type: holding
    address: 0x80
    bitmask: 0x80
  # Bit: 8
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Status BIT 1 Solar Energy Signal Input"
    id: "${devicename}_status_bit_1_solar_energy_signal_input"
    register_type: holding
    address: 0x80
    bitmask: 0x100
  # Bit: 9
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Status BIT 1 Anti Freezing Operation For Water Tank"
    id: "${devicename}_status_bit_1_anti_freezing_operation_for_water_tank"
    register_type: holding
    address: 0x80
    bitmask: 0x200
  # Bit: 10
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Status BIT 1 SG"
    id: "${devicename}_status_bit_1_sg"
    register_type: holding
    address: 0x80
    bitmask: 0x400
  # Bit: 11
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Status BIT 1 EUV"
    id: "${devicename}_status_bit_1_euv"
    register_type: holding
    address: 0x80
    bitmask: 0x800
  # Bit: 12
  - platform: modbus_controller
    name: "${entity_prefix} Status BIT 1 Reserved BIT 12"
    modbus_controller_id: "${devicename}"
    id: "${devicename}_status_bit_1_reserved_bit_12"
    register_type: holding
    address: 0x80
    bitmask: 0x1000
  # Bit: 13
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Status BIT 1 Request Serial Number Code"
    id: "${devicename}_status_bit_1_request_serial_number_code"
    register_type: holding
    address: 0x80
    bitmask: 0x2000
  # Bit: 14
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Status BIT 1 Request Software Version"
    id: "${devicename}_status_bit_1_request_software_version"
    register_type: holding
    address: 0x80
    bitmask: 0x4000
  # Bit: 15
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Status BIT 1 Request Operation Parameter"
    id: "${devicename}_status_bit_1_request_operation_parameter"
    register_type: holding
    address: 0x80
    bitmask: 0x8000

  # Register: 129
  # Bit: 0
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Load Output Electric Heater IBH 1"
    id: "${devicename}_load_output_electric_heater_ibh1"
    register_type: holding
    address: 0x81
    bitmask: 0x1
  # Bit: 1
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Load Output Electric Heater IBH 2"
    id: "${devicename}_load_output_reserved"
    register_type: holding
    address: 0x81
    bitmask: 0x2
  # Bit: 2
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Load Output Electric Heater TBH"
    id: "${devicename}_load_output_electric_heater_tbh"
    register_type: holding
    address: 0x81
    bitmask: 0x4
  # Bit: 3
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Load Output Water Pump PUMP_I"
    id: "${devicename}_load_output_water_pump_pump_i"
    register_type: holding
    address: 0x81
    bitmask: 0x8
  # Bit: 4
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Load Output SV 1"
    id: "${devicename}_load_output_sv1"
    register_type: holding
    address: 0x81
    bitmask: 0x10
  # Bit: 5
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Load Output Reserved BIT 5"
    id: "${devicename}_load_output_reserved_bit_5"
    register_type: holding
    address: 0x81
    bitmask: 0x20
  # Bit: 6
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Load Output External Water Pump P_o"
    id: "${devicename}_load_output_external_water_pump_p_o"
    register_type: holding
    address: 0x81
    bitmask: 0x40
  # Bit: 7
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Load Output Water Return Water P_d"
    id: "${devicename}_load_output_water_return_water_p_d"
    register_type: holding
    address: 0x81
    bitmask: 0x80
  # Bit: 8
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Load Output Mixed Water Pump P_c"
    id: "${devicename}_load_output_mixed_water_pump_p_c"
    register_type: holding
    address: 0x81
    bitmask: 0x100
  # Bit: 9
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Load Output SV 2"
    id: "${devicename}_load_output_sv2"
    register_type: holding
    address: 0x81
    bitmask: 0x200
  # Bit: 10
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Load Output HEAT 4"
    id: "${devicename}_load_output_heat4"
    register_type: holding
    address: 0x81
    bitmask: 0x400
  # Bit: 11
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Load Output Solar Water Pump"
    id: "${devicename}_load_output_solar_water_pump"
    register_type: holding
    address: 0x81
    bitmask: 0x800
  # Bit: 12
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Load Output ALARM"
    id: "${devicename}_load_output_alarm"
    register_type: holding
    entity_category: diagnostic
    address: 0x81
    bitmask: 0x1000
  # Bit: 13
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Load Output RUN"
    id: "${devicename}_load_output_run"
    register_type: holding
    address: 0x81
    bitmask: 0x2000
  # Bit: 14
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Load Output Auxiliary Heat Source"
    id: "${devicename}_load_output_auxiliary_heat_source"
    register_type: holding
    address: 0x81
    bitmask: 0x4000
  # Bit: 15
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Load Output DEFROST"
    id: "${devicename}_load_output_defrost"
    register_type: holding
    address: 0x81
    bitmask: 0x8000
  # Bit: 0

  # Register: 142
  # Bit: 0
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Slave Unit Online Status: Reserved BIT 0"
    id: "${devicename}_slave_unit_online_status_reserved_bit_0"
    register_type: holding
    address: 0x8e
    bitmask: 0x1
  # Bit: 1
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Slave Unit 1 Online Status"
    id: "${devicename}_slave_unit_1_online_status"
    register_type: holding
    address: 0x8e
    bitmask: 0x2
  # Bit: 2
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Slave Unit 2 Online Status"
    id: "${devicename}_slave_unit_2_online_status"
    register_type: holding
    address: 0x8e
    bitmask: 0x4
  # Bit: 3
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Slave Unit 3 Online Status"
    id: "${devicename}_slave_unit_3_online_status"
    register_type: holding
    address: 0x8e
    bitmask: 0x8
  # Bit: 4
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Slave Unit 4 Online Status"
    id: "${devicename}_slave_unit_4_online_status"
    register_type: holding
    address: 0x8e
    bitmask: 0x10
  # Bit: 5
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Slave Unit 5 Online Status"
    id: "${devicename}_slave_unit_5_online_status"
    register_type: holding
    address: 0x8e
    bitmask: 0x20
  # Bit: 6
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Slave Unit 6 Online Status"
    id: "${devicename}_slave_unit_6_online_status"
    register_type: holding
    address: 0x8e
    bitmask: 0x40
  # Bit: 7
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Slave Unit 7 Online Status"
    id: "${devicename}_slave_unit_7_online_status"
    register_type: holding
    address: 0x8e
    bitmask: 0x80
  # Bit: 8
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Slave Unit 8 Online Status"
    id: "${devicename}_slave_unit_8_online_status"
    register_type: holding
    address: 0x8e
    bitmask: 0x100
  # Bit: 9
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Slave Unit 9 Online Status"
    id: "${devicename}_slave_unit_9_online_status"
    register_type: holding
    address: 0x8e
    bitmask: 0x200
  # Bit: 10
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Slave Unit 10 Online Status"
    id: "${devicename}_slave_unit_10_online_status"
    register_type: holding
    address: 0x8e
    bitmask: 0x400
  # Bit: 11
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Slave Unit 11 Online Status"
    id: "${devicename}_slave_unit_11_online_status"
    register_type: holding
    address: 0x8e
    bitmask: 0x800
  # Bit: 12
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Slave Unit 12 Online Status"
    id: "${devicename}_slave_unit_12_online_status"
    register_type: holding
    address: 0x8e
    bitmask: 0x1000
  # Bit: 13
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Slave Unit 13 Online Status"
    id: "${devicename}_slave_unit_13_online_status"
    register_type: holding
    address: 0x8e
    bitmask: 0x2000
  # Bit: 14
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Slave Unit 14 Online Status"
    id: "${devicename}_slave_unit_14_online_status"
    register_type: holding
    address: 0x8e
    bitmask: 0x4000
  # Bit: 15
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Slave Unit 15 Online Status"
    id: "${devicename}_slave_unit_15_online_status"
    register_type: holding
    address: 0x8e
    bitmask: 0x8000

  # Register: 210, default: true, TODO: verify default
  # Bit: 0
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 1 Heating And Cooling First Or Water First"
    id: "${devicename}_parameter_setting_1_heating_and_cooling_first_or_water_first"
    register_type: holding
    address: 0xd2
    bitmask: 0x1
  # Bit: 1, default: false, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 1 Dual Room Thermostat Supported"
    id: "${devicename}_parameter_setting_1_dual_room_thermostat_supported"
    register_type: holding
    address: 0xd2
    bitmask: 0x2
  # Bit: 2, default: false, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 1 Room Thermostat"
    id: "${devicename}_parameter_setting_1_room_thermostat"
    register_type: holding
    address: 0xd2
    bitmask: 0x4
  # Bit: 3, default: true, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 1 Supports Room Thermostat"
    id: "${devicename}_parameter_setting_1_supports_room_thermostat"
    register_type: holding
    address: 0xd2
    bitmask: 0x8
  # Bit: 4, default: false, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 1 Supports Room Temperature Sensor Ta"
    id: "${devicename}_parameter_setting_1_supports_room_temperature_sensor_ta"
    register_type: holding
    address: 0xd2
    bitmask: 0x10
  # Bit: 5, default: false, TODO: verify default
  # Midea: PUMPI silent mode, 1; valid, 0: invalid
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 1 Supports T1 Sensor"
    id: "${devicename}_parameter_setting_1_supports_t1_sensor"
    register_type: holding
    address: 0xd2
    bitmask: 0x20
  # Bit: 6, default: false, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 1 T1S Heating High Low Temperature Settings"
    id: "${devicename}_parameter_setting_1_t1s_heating_high_low_temperature_settings"
    register_type: holding
    address: 0xd2
    bitmask: 0x40
  # Bit: 7, default: true, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 1 Enable Heating"
    id: "${devicename}_parameter_setting_1_enable_heating"
    register_type: holding
    address: 0xd2
    bitmask: 0x80
  # Bit: 8, default: false, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 1 T1s Cooling High Low Temperature Settings"
    id: "${devicename}_parameter_setting_1_t1s_cooling_high_low_temperature_settings"
    register_type: holding
    address: 0xd2
    bitmask: 0x100
  # Bit: 9, default: true, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 1 Enable Cooling"
    id: "${devicename}_parameter_setting_1_enable_cooling"
    register_type: holding
    address: 0xd2
    bitmask: 0x200
  # Bit: 10, default: false, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 1 DHW Pump Supports Pipe Disinfect"
    id: "${devicename}_parameter_setting_1_dhw_pump_supports_pipe_disinfect"
    register_type: holding
    address: 0xd2
    bitmask: 0x400
  # Bit: 11, default: false, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 1 Reserved BIT 11"
    id: "${devicename}_parameter_setting_1_reserved_bit_11"
    register_type: holding
    address: 0xd2
    bitmask: 0x800
  # Bit: 12, default: false, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 1 DHW Pump Supported"
    id: "${devicename}_parameter_setting_1_dhw_pump_supported"
    register_type: holding
    address: 0xd2
    bitmask: 0x1000
  # Bit: 13, default: true, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 1 Supports Disinfection"
    id: "${devicename}_parameter_setting_1_supports_disinfection"
    register_type: holding
    address: 0xd2
    bitmask: 0x2000
  # Bit: 14, default: true, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 1 Supports Water Tank Electric Heater TBH"
    id: "${devicename}_parameter_setting_1_supports_water_tank_electric_heater_tbh"
    register_type: holding
    address: 0xd2
    bitmask: 0x4000
  # Bit: 15, default: true, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 1 Enable Water Heating"
    id: "${devicename}_parameter_setting_1_enable_water_heating"
    register_type: holding
    address: 0xd2
    bitmask: 0x8000

  # Register: 211
  # Bit: 0, default: false, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 2 IBH AHS Installation Position"
    id: "${devicename}_parameter_setting_2_ibh_ahs_installation_position"
    register_type: holding
    address: 0xd3
    bitmask: 0x1
  # Bit: 1, default: false, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 2 Tbt Sensor Enable"
    id: "${devicename}_parameter_setting_2_tbt_sensor_enable"
    register_type: holding
    address: 0xd3
    bitmask: 0x2
  # Bit: 2, default: false, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 2 Ta Sensor Position"
    id: "${devicename}_parameter_setting_2_ta_sensor_position"
    register_type: holding
    address: 0xd3
    bitmask: 0x4
  # Bit: 3, default: false, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 2 Double Zone Setting Is Valid"
    id: "${devicename}_parameter_setting_2_double_zone_setting_is_valid"
    register_type: holding
    address: 0xd3
    bitmask: 0x8
  # Bit: 4, default: false, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 2 Setting The High Low Temperature Of Heating Mode T1S"
    id: "${devicename}_parameter_setting_2_setting_the_high_low_temperature_of_heating_mode_t1s"
    register_type: holding
    address: 0xd3
    bitmask: 0x10
  # Bit: 5, default: false, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 2 Setting The High Low Temperature Of Cooling Mode T1S"
    id: "${devicename}_parameter_setting_2_setting_the_high_low_temperature_of_cooling_mode_t1s"
    register_type: holding
    address: 0xd3
    bitmask: 0x20
  # Bit: 6, default: false, TODO: verify default
  # Midea: T1B sensor enable
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 2 Tw2 Enabled"
    id: "${devicename}_parameter_setting_2_tw2_enabled"
    register_type: holding
    address: 0xd3
    bitmask: 0x40
  # Bit: 7, default: false, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 2 Smart Grid"
    id: "${devicename}_parameter_setting_2_smart_grid"
    register_type: holding
    address: 0xd3
    bitmask: 0x80
  # Bit: 8, default: false, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 2 Port Definition"
    id: "${devicename}_parameter_setting_2_port_definition"
    register_type: holding
    address: 0xd3
    bitmask: 0x100
  # Bit: 9, default: false, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 2 Solar Energy Kit Enable"
    id: "${devicename}_parameter_setting_2_solar_energy_kit_enable"
    register_type: holding
    address: 0xd3
    bitmask: 0x200
  # Bit: 10, default: false, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 2 Solar Energy Input Port"
    id: "${devicename}_parameter_setting_2_solar_energy_input_port"
    register_type: holding
    address: 0xd3
    bitmask: 0x400
  # Bit: 11, default: false, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 2 Piping Length Selection"
    id: "${devicename}_parameter_setting_2_piping_length_selection"
    register_type: holding
    address: 0xd3
    bitmask: 0x800
  # Bit: 12, default: false, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 2 Tbt2 Sensor Is Valid"
    id: "${devicename}_parameter_setting_2_tbt2_sensor_is_valid"
    register_type: holding
    address: 0xd3
    bitmask: 0x1000
  # Bit: 13, default: false, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 2 Enable Temperature Collection Kit"
    id: "${devicename}_parameter_setting_2_enable_temperature_collection_kit"
    register_type: holding
    address: 0xd3
    bitmask: 0x2000
  # Bit: 14, default: false, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 2 M1M2 Is Used For AHS Control"
    id: "${devicename}_parameter_setting_2_m1m2_is_used_for_ahs_control"
    register_type: holding
    address: 0xd3
    bitmask: 0x4000
  # Bit: 15, default: false, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Parameter Setting 2 Reserved BIT 15"
    id: "${devicename}_parameter_setting_2_reserved_bit_15"
    register_type: holding
    address: 0xd3
    bitmask: 0x8000
  # Template binary sensor which shows if the heat pump is running
  - platform: template
    name: "${entity_prefix} Heat pump running"
    id: "${devicename}_heat_pump_running"
    lambda: |-
      int fan_speed = id(${devicename}_fan_speed).state;
      int compressor_frequency = id(${devicename}_compressor_operating_frequency).state;
      bool external_water_pump_on = id(${devicename}_load_output_external_water_pump_p_o).state;

      // If fan_speed is above 0, compressor_frequency is above 0 or external_water_pump_on is true,
      // then the outside unit of the heat pump system is running
      if (fan_speed > 0 || compressor_frequency > 0 || external_water_pump_on) {
          return true;
      } else {
          return false;
      }

switch:
  - platform: factory_reset
    name: Restart with Factory Default Settings
  # Register: 0 -> Bit 2
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Power DHW T5S"
    id: "${devicename}_power_dhw_t5s"
    register_type: holding
    entity_category: config
    address: 0x0
    bitmask: 0x4
  # Register: 5 -> Bit 12
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Weather Compensation Zone 1"
    id: "${devicename}_weather_compensation_zone_1"
    register_type: holding
    entity_category: config
    address: 0x5
    bitmask: 0x1000
  # Register: 5 -> Bit 13
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Weather Compensation Zone 2"
    id: "${devicename}_weather_compensation_zone_2"
    register_type: holding
    entity_category: config
    address: 0x5
    bitmask: 0x2000

  # Register: 7
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Forced Water Tank Heating On/Off"
    id: "${devicename}_forced_water_tank_heating_on_off"
    icon: mdi:fire-alert
    address: 0x7
    register_type: holding
    entity_category: config
    write_lambda: |-
      uint16_t value = 0;

      if (x == 1) {
        ESP_LOGI("main", "Set forced water tank heating ON");
        value = 1;
      } else {
        ESP_LOGI("main", "Set forced water tank heating OFF");
        value = 2;
      }

      esphome::modbus_controller::ModbusCommandItem set_payload_command = esphome::modbus_controller::ModbusCommandItem::create_write_single_command(${devicename}, 0x7, value);
      ${devicename}->queue_command(set_payload_command);

      return {};

number:
  # Register: 2 (Zone 1, Low)
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Set Water Temperature T1S Zone 1"
    id: "${devicename}_set_water_temperature_t1s_zone_1"
    register_type: holding
    address: 0x2
    value_type: U_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: 5
    max_value: 60
    mode: slider
    lambda: |-
      // Update the global var unmasked_value_water_temperature_t1s
      id(unmasked_value_water_temperature_t1s) = x;

      // ESP_LOGI("","unmasked_value_water_temperature_t1s: %d",id(unmasked_value_water_temperature_t1s));

      uint8_t value_bytes[2];
      uint16_t value = x;
      value_bytes[0] = value >> 8;     // high byte (zone 2)
      value_bytes[1] = value & 0x00FF; // low byte (zone 1)

      // ESP_LOGI("","Zone 1 is %d", value_bytes[1]);
      // ESP_LOGI("","Zone 2 is %d", value_bytes[0]);

      return value_bytes[1];
    write_lambda: |-
      uint16_t value = id(unmasked_value_water_temperature_t1s); // The original unmasked value
      uint8_t value_byte = x;                                    // New byte value with the new temp for zone 1

      value &= 0xFF00;      // Clear the lower byte of the value
      value |= value_byte;  // Update the lower byte with the new byte value

      // ESP_LOGI("main", "Original value: %d", id(unmasked_value_water_temperature_t1s));
      // ESP_LOGI("main", "New value: %d", value);

      esphome::modbus_controller::ModbusCommandItem set_payload_command = esphome::modbus_controller::ModbusCommandItem::create_write_single_command(${devicename}, 0x2, value);
      ${devicename}->queue_command(set_payload_command);

      return {};

  # Register: 2 (Zone 2, High)
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Set Water Temperature T1S Zone 2"
    id: "${devicename}_set_water_temperature_t1s_zone_2"
    register_type: holding
    address: 0x2
    value_type: U_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: 5
    max_value: 60
    mode: slider
    lambda: |-
      // The global var unmasked_value_water_temperature_t1s is already
      // updated in the previous, where the low byte variant is executed
      // id(unmasked_value_water_temperature_t1s) = x;

      uint8_t value_bytes[2];
      uint16_t value = x;
      value_bytes[0] = value >> 8;     // high byte (zone 2)
      value_bytes[1] = value & 0x00FF; // low byte (zone 1)

      return value_bytes[0];
    write_lambda: |-
      uint16_t value = id(unmasked_value_water_temperature_t1s); // The original unmasked value
      uint8_t value_byte = x;                                    // New byte value with the new temp for zone 2

      value &= 0x00FF;             // Clear the upper byte of the value
      value |= (value_byte << 8);  // Update the upper byte with the new byte value

      esphome::modbus_controller::ModbusCommandItem set_payload_command = esphome::modbus_controller::ModbusCommandItem::create_write_single_command(${devicename}, 0x2, value);
      ${devicename}->queue_command(set_payload_command);

      return {};

  # Register: 4
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Set DHW Tank Temperature T5s"
    id: "${devicename}_set_dhw_tank_temperature_t5s"
    register_type: holding
    address: 0x4
    value_type: U_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: 20
    max_value: 60
    mode: slider

  # Register: 6 (Zone 1, Low)
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Weather Compensation Curve Zone 1"
    id: "${devicename}_weather_compensation_curve_zone_1"
    register_type: holding
    address: 0x6
    value_type: U_WORD
    entity_category: config
    min_value: 1
    max_value: 9
    mode: slider
    lambda: |-
      // Update the global var unmasked_curve_selection
      id(unmasked_curve_selection) = x;

      // ESP_LOGI("","unmasked_curve_selection: %d",id(unmasked_curve_selection));

      uint8_t value_bytes[2];
      uint16_t value = x;
      value_bytes[0] = value >> 8;     // high byte (zone 2)
      value_bytes[1] = value & 0x00FF; // low byte (zone 1)

      // ESP_LOGI("","Zone 1 is %d", value_bytes[1]);
      // ESP_LOGI("","Zone 2 is %d", value_bytes[0]);

      return value_bytes[1];
    write_lambda: |-
      uint16_t value = id(unmasked_curve_selection); // The original unmasked value
      uint8_t value_byte = x;                        // New byte value with the new temp for zone 1

      value &= 0xFF00;      // Clear the lower byte of the value
      value |= value_byte;  // Update the lower byte with the new byte value

      // ESP_LOGI("main", "Original value: %d", id(unmasked_curve_selection));
      // ESP_LOGI("main", "New value: %d", value);

      esphome::modbus_controller::ModbusCommandItem set_payload_command = esphome::modbus_controller::ModbusCommandItem::create_write_single_command(${devicename}, 0x6, value);
      ${devicename}->queue_command(set_payload_command);

      return {};
  # Register: 6 (Zone 2, High)
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Weather Compensation Curve Zone 2"
    id: "${devicename}_weather_compensation_curve_zone_2"
    register_type: holding
    address: 0x6
    value_type: U_WORD
    entity_category: config
    min_value: 1
    max_value: 9
    mode: slider
    lambda: |-
      // The global var unmasked_curve_selection is already
      // updated in the previous, where the low byte variant is executed
      // id(unmasked_curve_selection) = x;

      uint8_t value_bytes[2];
      uint16_t value = x;
      value_bytes[0] = value >> 8;     // high byte (zone 2)
      value_bytes[1] = value & 0x00FF; // low byte (zone 1)

      return value_bytes[0];
    write_lambda: |-
      uint16_t value = id(unmasked_curve_selection); // The original unmasked value
      uint8_t value_byte = x;                        // New byte value with the new temp for zone 2

      value &= 0x00FF;             // Clear the upper byte of the value
      value |= (value_byte << 8);  // Update the upper byte with the new byte value

      esphome::modbus_controller::ModbusCommandItem set_payload_command = esphome::modbus_controller::ModbusCommandItem::create_write_single_command(${devicename}, 0x6, value);
      ${devicename}->queue_command(set_payload_command);

      return {};

  # Register: 205, default: 60, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Temperature Upper Limit Of TS Setting"
    id: "${devicename}_temperature_upper_limit_of_ts_setting"
    register_type: holding
    address: 0xcd
    value_type: S_WORD
    unit_of_measurement: "°C"
    entity_category: config
  # Register: 206, default: 34, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Temperature Lower Limit Of TS Setting"
    id: "${devicename}_temperature_lower_limit_of_ts_setting"
    register_type: holding
    address: 0xce
    value_type: S_WORD
    unit_of_measurement: "°C"
    entity_category: config
  # Register: 207, default: 60, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Temperature Upper Limit Of water Heating"
    id: "${devicename}_temperature_upper_limit_of_water_heating"
    register_type: holding
    address: 0xcf
    value_type: S_WORD
    unit_of_measurement: "°C"
    entity_category: config
  # Register: 208, default: 20, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Temperature Lower Limit Of Water Heating"
    id: "${devicename}_temperature_lower_limit_of_water_heating"
    register_type: holding
    address: 0xd0
    value_type: S_WORD
    unit_of_measurement: "°C"
    entity_category: config
  # Register: 209, default: 5
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} DHW Pump Return Running Time"
    id: "${devicename}_dhw_pump_return_running_time"
    register_type: holding
    address: 0xd1
    value_type: U_WORD
    unit_of_measurement: min
    entity_category: config
    min_value: 5
    max_value: 120
  # Register: 212, default: 5
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} dT5_On"
    id: "${devicename}_dt5_on"
    register_type: holding
    address: 0xd4
    value_type: U_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: 2
    max_value: 10
  # Register: 213, default: 10
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} dT1S5"
    id: "${devicename}_dt1s5"
    register_type: holding
    address: 0xd5
    value_type: U_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: 5
    max_value: 40
  # Register: 214, default: 5
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} T Interval DHW"
    id: "${devicename}_t_interval_dhw"
    register_type: holding
    address: 0xd6
    value_type: U_WORD
    unit_of_measurement: min
    entity_category: config
    min_value: 5
    max_value: 30
  # Register: 215, default: 43
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} T4 DHW max"
    id: "${devicename}_t4_dhw_max"
    register_type: holding
    address: 0xd7
    value_type: U_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: 35
    max_value: 43
  # Register: 216, default: -10
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} T4 DHW min"
    id: "${devicename}_t4dhwmin"
    register_type: holding
    address: 0xd8
    value_type: S_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: -25
    max_value: 5
  # Register: 217, default: 30
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} t TBH Delay"
    id: "${devicename}_t_tbh_delay"
    register_type: holding
    address: 0xd9
    value_type: U_WORD
    unit_of_measurement: min
    entity_category: config
    min_value: 0
    max_value: 240
    step: 5
  # Register: 218, default: 5
  # Also known as dT5S TBH Off (dt5s_tbh_off)
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} dT5 TBH Off"
    id: "${devicename}_dt5_tbh_off"
    register_type: holding
    address: 0xda
    value_type: U_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: 0
    max_value: 10
  # Register: 219, default: 5
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} T4 TBH On"
    id: "${devicename}_t4_tbh_on"
    register_type: holding
    address: 0xdb
    value_type: S_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: -5
    max_value: 20
  # Register: 220, default: 65
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Temperature For Disinfection Operation"
    id: "${devicename}_t5s_di"
    register_type: holding
    address: 0xdc
    value_type: U_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: 60
    max_value: 70
  # Register: 221, default: 210
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Maximum Disinfection Duration"
    id: "${devicename}_t_di_max"
    register_type: holding
    address: 0xdd
    value_type: U_WORD
    unit_of_measurement: min
    entity_category: config
    min_value: 90
    max_value: 300
  # Register: 222, default: 15
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Disinfection High Temperature Duration"
    id: "${devicename}_t_di_hightemp"
    register_type: holding
    address: 0xde
    value_type: U_WORD
    unit_of_measurement: min
    entity_category: config
    min_value: 5
    max_value: 60
  # Register: 223, default: 5
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Time Interval Of Compressor Startup In Cooling mode"
    id: "${devicename}_t_interval_c"
    register_type: holding
    address: 0xdf
    value_type: U_WORD
    unit_of_measurement: min
    entity_category: config
    min_value: 5
    max_value: 30
  # Register: 224, default: 5
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} dT1SC"
    id: "${devicename}_dt1sc"
    register_type: holding
    address: 0xe0
    value_type: U_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: 2
    max_value: 10
  # Register: 225, default: 2
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} dTSC"
    id: "${devicename}_dtsc"
    register_type: holding
    address: 0xe1
    value_type: U_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: 1
    max_value: 10
  # Register: 226, default: 43
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} T4cmax"
    id: "${devicename}_t4cmax"
    register_type: holding
    address: 0xe2
    value_type: U_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: 35
    max_value: 46
  # Register: 227, default: 10
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} T4cmin"
    id: "${devicename}_t4cmin"
    register_type: holding
    address: 0xe3
    value_type: S_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: -5
    max_value: 25
  # Register: 228, default: 5
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Time Interval Of Compressor Startup In Heating mode"
    id: "${devicename}_t_interval_h"
    register_type: holding
    address: 0xe4
    value_type: U_WORD
    unit_of_measurement: min
    entity_category: config
    min_value: 5
    max_value: 60
  # Register: 229, default: 5
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} dT1SH"
    id: "${devicename}_dt1sh"
    register_type: holding
    address: 0xe5
    value_type: U_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: 2
    max_value: 10
  # Register: 230, default: 2
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} dTSH"
    id: "${devicename}_dtsh"
    register_type: holding
    address: 0xe6
    value_type: U_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: 1
    max_value: 10
  # Register: 231, default: 25
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} T4hmax"
    id: "${devicename}_t4hmax"
    register_type: holding
    address: 0xe7
    value_type: U_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: 20
    max_value: 35
  # Register: 232, default: -15
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} T4hmin"
    id: "${devicename}_t4hmin"
    register_type: holding
    address: 0xe8
    value_type: S_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: -25
    max_value: 5
  # Register: 233, default: -5
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Ambient Temperature For Enabling Hydraulic Module Auxiliary Electric Heating IBH"
    id: "${devicename}_t4_ibh_on"
    register_type: holding
    address: 0xe9
    value_type: S_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: -15
    max_value: 10
  # Register: 234, default: 5
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Temperature Return Difference For Enabling The Hydraulic Module Auxiliary IBH"
    id: "${devicename}_dt1_ibh_on"
    register_type: holding
    address: 0xea
    value_type: S_WORD
    unit_of_measurement: "°C"
    entity_category: config
  # Register: 235, default: 30
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Delay Time Of Enabling The Hydraulic Module Auxiliary Electric Heating IBH"
    id: "${devicename}_t_ibh_delay"
    register_type: holding
    address: 0xeb
    value_type: U_WORD
    unit_of_measurement: min
    entity_category: config
  # Register: 237, default: 10, TODO: verify default
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Ambient Temperature Trigger For AHS"
    id: "${devicename}_t4_ahs_on"
    register_type: holding
    address: 0xed
    value_type: S_WORD
    unit_of_measurement: "°C"
    entity_category: config
  # Register: 238, default: 5
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Trigger Temperature Difference Between T1S And Current Heat for AHS"
    id: "${devicename}_dt1_ahs_on"
    register_type: holding
    address: 0xee
    value_type: S_WORD
    unit_of_measurement: "°C"
    entity_category: config
  # Register: 240, default: 30
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Delay Time for Enabling AHS"
    id: "${devicename}_t_ahs_delay"
    register_type: holding
    address: 0xf0
    value_type: U_WORD
    unit_of_measurement: min
    entity_category: config
    min_value: 5
    max_value: 120
  # Register: 241, default: 120
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Water Heating Max Duration"
    id: "${devicename}_t_dhwhp_max"
    register_type: holding
    address: 0xf1
    value_type: U_WORD
    unit_of_measurement: min
    entity_category: config
    min_value: 10
    max_value: 600
  # Register: 242, default: 30
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} T DHWHP Restrict"
    id: "${devicename}_t_dhwhp_restrict"
    register_type: holding
    address: 0xf2
    value_type: U_WORD
    unit_of_measurement: min
    entity_category: config
    min_value: 10
    max_value: 600
  # Register: 243, default: 25
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} T4autocmin"
    id: "${devicename}_t4autocmin"
    register_type: holding
    address: 0xf3
    value_type: U_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: 20
    max_value: 29
  # Register: 244, default: 17
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} T4autohmax"
    id: "${devicename}_t4autohmax"
    register_type: holding
    address: 0xf4
    value_type: U_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: 10
    max_value: 17
  # Register: 245, default: 25
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Heating Or Cooling Temperature When Holiday Mode Is Active"
    id: "${devicename}_t1s_h_a_h"
    register_type: holding
    address: 0xf5
    value_type: U_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: 20
    max_value: 29
  # Register: 246, default: 25
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Domestic Hot Water Temperature When Holiday Mode is Active"
    id: "${devicename}_t5s_h_a_dhw"
    register_type: holding
    address: 0xf6
    value_type: U_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: 20
    max_value: 25
  # Register: 247, default: 10
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} PER START Ratio"
    id: "${devicename}_per_start_ratio"
    register_type: holding
    address: 0xf7
    value_type: U_WORD
    entity_category: config
    min_value: 10
    max_value: 100
    step: 10
  # Register: 248, default: 5
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} TIME ADJUST"
    id: "${devicename}_time_adjust"
    register_type: holding
    address: 0xf8
    value_type: U_WORD
    entity_category: config
    min_value: 1
    max_value: 60
  # Register: 249, default: 15
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} DTbt2"
    id: "${devicename}_dtbt2"
    register_type: holding
    address: 0xf9
    value_type: U_WORD
    entity_category: config
    min_value: 0
    max_value: 50
  # Register: 250, default: 0
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} IBH1 Power"
    id: "${devicename}_ibh1_power"
    register_type: holding
    address: 0xfa
    value_type: U_WORD
    unit_of_measurement: W
    entity_category: config
    min_value: 0
    max_value: 200
  # Register: 251, default: 0
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} IBH2 Power"
    id: "${devicename}_ibh2_power"
    register_type: holding
    address: 0xfb
    value_type: U_WORD
    unit_of_measurement: W
    entity_category: config
    min_value: 0
    max_value: 200
  # Register: 252, default: 0
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} TBH Power"
    id: "${devicename}_tbh_power"
    register_type: holding
    address: 0xfc
    value_type: U_WORD
    unit_of_measurement: W
    entity_category: config
    min_value: 0
    max_value: 200
  # Register: 255, default: 8
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Temperature Rise Day Number"
    id: "${devicename}_t_dryup"
    register_type: holding
    address: 0xff
    value_type: U_WORD
    entity_category: config
    min_value: 4
    max_value: 15
  # Register: 256, default: 5
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Drying Day Number"
    id: "${devicename}_t_highpeak"
    register_type: holding
    address: 0x100
    value_type: U_WORD
    entity_category: config
    min_value: 3
    max_value: 7
  # Register: 257, default: 5
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Temperature Drop Day Number"
    id: "${devicename}_t_dryd"
    register_type: holding
    address: 0x101
    value_type: U_WORD
    entity_category: config
    min_value: 4
    max_value: 15
  # Register: 258, default: 45
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Highest Drying Temperature"
    id: "${devicename}_t_drypeak"
    register_type: holding
    address: 0x102
    value_type: S_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: 30
    max_value: 55
  # Register: 259, default: 72
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} Running Time Of Floor Heating For The First Time"
    id: "${devicename}_t_firstfh"
    register_type: holding
    address: 0x103
    value_type: U_WORD
    unit_of_measurement: hr
    entity_category: config
    min_value: 48
    max_value: 96
  # Register: 260, default: 25
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} T1S Of Floor Heating For The First Time"
    id: "${devicename}_t1s_firstfh"
    register_type: holding
    address: 0x104
    value_type: U_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: 25
    max_value: 35
  # Register: 261, default: 10
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} T1SetC1"
    id: "${devicename}_t1setc1"
    register_type: holding
    address: 0x105
    value_type: U_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: 5
    max_value: 25
  # Register: 262, default: 16
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} T1SetC2"
    id: "${devicename}_t1setc2"
    register_type: holding
    address: 0x106
    value_type: U_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: 5
    max_value: 25
  # Register: 263, default: 35
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} T4C1"
    id: "${devicename}_t4c1"
    register_type: holding
    address: 0x107
    value_type: S_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: -5
    max_value: 46
  # Register: 264, default: 25
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} T4C2"
    id: "${devicename}_t4c2"
    register_type: holding
    address: 0x108
    value_type: S_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: -5
    max_value: 46
  # Register: 265, default: 35
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} T1SetH1"
    id: "${devicename}_t1seth1"
    register_type: holding
    address: 0x109
    value_type: U_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: 25
    max_value: 65
  # Register: 266, default: 28
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} T1SetH2"
    id: "${devicename}_t1seth2"
    register_type: holding
    address: 0x10a
    value_type: U_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: 25
    max_value: 65
  # Register: 267, default: -5
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} T4H1"
    id: "${devicename}_t4h1"
    register_type: holding
    address: 0x10b
    value_type: S_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: -25
    max_value: 30
  # Register: 268, default: 7
  - platform: modbus_controller
    modbus_controller_id: "${devicename}"
    name: "${entity_prefix} T4H2"
    id: "${devicename}_t4h2"
    register_type: holding
    address: 0x10c
    value_type: S_WORD
    unit_of_measurement: "°C"
    entity_category: config
    min_value: -25
    max_value: 30

text_sensor:
  - platform: version
    name: "ESPHome Version"
    hide_timestamp: true
  # Active State
  - platform: template
    name: "${entity_prefix} Active State"
    id: "${devicename}_active_state"
    lambda: |-
      if (id(${devicename}_load_output_run).state) {
        // The heat pump is on
        if (id(${devicename}_status_bit_1_defrosting).state) {
          return {"Defrosting"};
        } else if (id(${devicename}_load_output_sv1).state) {
          return {"DHW"};
        } else {
          if (id(${devicename}_status_bit_1_heating_mode_set_by_room_thermostat).state) {
            return {"Heating"};
          } else if (id(${devicename}_status_bit_1_cooling_mode_set_by_room_thermostat).state) {
            return {"Cooling"};
          } else {
            return {"Unknown"};
          }
        }
      } else {
        // The heat pump is off
        return {"Inactive"};
      }
  # Current fault mapped to error code
  - platform: template
    name: "${entity_prefix} Current Fault Error Code"
    id: "${devicename}_current_fault_error_code"
    lambda: |-
      int current_fault = id(${devicename}_current_fault).state;

      // ESP_LOGI("main", "Current fault: %d", current_fault);

      if (current_fault >= 0 && current_fault <= 143) {
        return std::to_string(current_fault);
      } else {
        return {"Unknown"};
      }
    filters:
      - map:
        - 0 -> OK
        - 1 -> E0
        - 2 -> E1
        - 3 -> E2
        - 4 -> E3
        - 5 -> E4
        - 6 -> E5
        - 7 -> E6
        - 8 -> E7
        - 9 -> E8
        - 10 -> E9
        - 11 -> EA
        - 12 -> Eb
        - 13 -> Ec
        - 14 -> Ed
        - 15 -> EE
        - 20 -> P0
        - 21 -> P1
        - 23 -> P3
        - 24 -> P4
        - 25 -> P5
        - 26 -> P6
        - 31 -> Pb
        - 33 -> Pd
        - 38 -> PP
        - 39 -> H0
        - 40 -> H1
        - 41 -> H2
        - 42 -> H3
        - 43 -> H4
        - 44 -> H5
        - 45 -> H6
        - 46 -> H7
        - 47 -> H8
        - 48 -> H9
        - 49 -> HA
        - 50 -> Hb
        - 52 -> Hd
        - 53 -> HE
        - 54 -> HF
        - 55 -> HH
        - 57 -> HP
        - 65 -> C7
        - 112 -> bH
        - 116 -> F1
        - 134 -> L0
        - 135 -> L1
        - 136 -> L2
        - 138 -> L4
        - 139 -> L5
        - 141 -> L7
        - 142 -> L8
        - 143 -> L9
  # Current fault mapped to error code description
  - platform: template
    name: "${entity_prefix} Current Fault Error Code Description"
    id: "${devicename}_current_fault_error_code_description"
    lambda: |-
      int current_fault = id(${devicename}_current_fault).state;

      // ESP_LOGI("main", "Current fault: %d", current_fault);

      if (current_fault >= 0 && current_fault <= 143) {
        return std::to_string(current_fault);
      } else {
        return {"Unknown"};
      }
    filters:
      - map:
        - 0 -> OK
        - 1 -> Water flow fault(E8 displayed 3 times)
        - 2 -> Phase loss or neutral wire and live wire are connected reversely(only for three phase unit)
        - 3 -> Communication fault between controller and hydraulic module
        - 4 -> Final outlet water temp. sensor(T1) fault
        - 5 -> Water tank temp. sensor(T5) fault
        - 6 -> The condenser outlet refrigerant temperature sensor(T3) fault
        - 7 -> The ambient temperature sensor(T4) fault
        - 8 -> Buffer tank up temp. sensor(Tbt1) fault
        - 9 -> Water flow failure
        - 10 -> Suction temp. sensor (Th) fault
        - 11 -> Discharge temp. sensor (Tp) fault
        - 12 -> Solar temp. sensor(Tsolar) fault
        - 13 -> Buffer tank low temp. sensor(Tbt2) fault
        - 14 -> Inlet water temp. sensor(Tw_in) malfunction
        - 15 -> Hydraulic module EEprom failure
        - 20 -> Low pressure switch protection
        - 21 -> High pressure switch protection
        - 23 -> Compressor overcurrent protection
        - 24 -> High discharge temperature protection
        - 25 -> |Tw_out - Tw_in| value too big protection
        - 26 -> Inverter module protection
        - 31 -> Anti-freeze mode
        - 33 -> High temperature protection of refrigerant outlet temp. of condenser
        - 38 -> Tw_out - Tw_in unusual protection
        - 39 -> Communication fault between main board PCB B and main control board of hydraulic module
        - 40 -> Communication fault between inverter module PCB A and main control board PCB B
        - 41 -> Refrigerant liquid temp. sensor(T2) fault
        - 42 -> Refrigerant gas temp. sensor(T2B) fault
        - 43 -> Three times P6(L0/L1) protection
        - 44 -> Room temo. sensor (Ta) fault
        - 45 -> DC fan motor fault
        - 46 -> Voltage protection
        - 47 -> Pressure sensor fault
        - 48 -> Outlet water for zone 2 temp. sensor(Tw2) fault
        - 49 -> Outlet water temp. sensor(Tw_out) fault
        - 50 -> 3 times PP protection and Tw_out<7℃
        - 52 -> Communication fault between hydraulic module parallel
        - 53 -> Communication error between main board and thermostat transfer board
        - 54 -> Inverter module board EE PROM fault
        - 55 -> H6 display 10 times in 2 hours
        - 57 -> Low pressure protection (Pe<0.6) occurred 3 times in 1 hour
        - 65 -> Transducer module temperature too high protection
        - 112 -> PED PCB fault
        - 116 -> Low DC generatrix voltage protection
        - 134 -> Module protection
        - 135 -> DC generatrix low voltage protection
        - 136 -> DC generatrix high voltage protection
        - 138 -> MCE fault
        - 139 -> Zero speed protection
        - 141 -> Phase sequence fault
        - 142 -> Speed difference > 15Hz protection between the front and the back clock
        - 143 -> Speed difference > 15Hz protection between the real and the setting speed
  # Fault 1 mapped to error code
  - platform: template
    name: "${entity_prefix} Fault 1 Error Code"
    id: "${devicename}_fault_1_error_code"
    lambda: |-
      int fault_one = id(${devicename}_fault_1).state;

      if (fault_one >= 0 && fault_one <= 143) {
        return std::to_string(fault_one);
      } else {
        return {"Unknown"};
      }
    filters:
      - map:
        - 0 -> OK
        - 1 -> E0
        - 2 -> E1
        - 3 -> E2
        - 4 -> E3
        - 5 -> E4
        - 6 -> E5
        - 7 -> E6
        - 8 -> E7
        - 9 -> E8
        - 10 -> E9
        - 11 -> EA
        - 12 -> Eb
        - 13 -> Ec
        - 14 -> Ed
        - 15 -> EE
        - 20 -> P0
        - 21 -> P1
        - 23 -> P3
        - 24 -> P4
        - 25 -> P5
        - 26 -> P6
        - 31 -> Pb
        - 33 -> Pd
        - 38 -> PP
        - 39 -> H0
        - 40 -> H1
        - 41 -> H2
        - 42 -> H3
        - 43 -> H4
        - 44 -> H5
        - 45 -> H6
        - 46 -> H7
        - 47 -> H8
        - 48 -> H9
        - 49 -> HA
        - 50 -> Hb
        - 52 -> Hd
        - 53 -> HE
        - 54 -> HF
        - 55 -> HH
        - 57 -> HP
        - 65 -> C7
        - 112 -> bH
        - 116 -> F1
        - 134 -> L0
        - 135 -> L1
        - 136 -> L2
        - 138 -> L4
        - 139 -> L5
        - 141 -> L7
        - 142 -> L8
        - 143 -> L9
  # Fault 2 mapped to error code
  - platform: template
    name: "${entity_prefix} Fault 2 Error Code"
    id: "${devicename}_fault_2_error_code"
    lambda: |-
      int fault_two = id(${devicename}_fault_2).state;

      if (fault_two >= 0 && fault_two <= 143) {
        return std::to_string(fault_two);
      } else {
        return {"Unknown"};
      }
    filters:
      - map:
        - 0 -> OK
        - 1 -> E0
        - 2 -> E1
        - 3 -> E2
        - 4 -> E3
        - 5 -> E4
        - 6 -> E5
        - 7 -> E6
        - 8 -> E7
        - 9 -> E8
        - 10 -> E9
        - 11 -> EA
        - 12 -> Eb
        - 13 -> Ec
        - 14 -> Ed
        - 15 -> EE
        - 20 -> P0
        - 21 -> P1
        - 23 -> P3
        - 24 -> P4
        - 25 -> P5
        - 26 -> P6
        - 31 -> Pb
        - 33 -> Pd
        - 38 -> PP
        - 39 -> H0
        - 40 -> H1
        - 41 -> H2
        - 42 -> H3
        - 43 -> H4
        - 44 -> H5
        - 45 -> H6
        - 46 -> H7
        - 47 -> H8
        - 48 -> H9
        - 49 -> HA
        - 50 -> Hb
        - 52 -> Hd
        - 53 -> HE
        - 54 -> HF
        - 55 -> HH
        - 57 -> HP
        - 65 -> C7
        - 112 -> bH
        - 116 -> F1
        - 134 -> L0
        - 135 -> L1
        - 136 -> L2
        - 138 -> L4
        - 139 -> L5
        - 141 -> L7
        - 142 -> L8
        - 143 -> L9
  # Fault 3 mapped to error code
  - platform: template
    name: "${entity_prefix} Fault 3 Error Code"
    id: "${devicename}_fault_3_error_code"
    lambda: |-
      int fault_three = id(${devicename}_fault_3).state;

      if (fault_three >= 0 && fault_three <= 143) {
        return std::to_string(fault_three);
      } else {
        return {"Unknown"};
      }
    filters:
      - map:
        - 0 -> OK
        - 1 -> E0
        - 2 -> E1
        - 3 -> E2
        - 4 -> E3
        - 5 -> E4
        - 6 -> E5
        - 7 -> E6
        - 8 -> E7
        - 9 -> E8
        - 10 -> E9
        - 11 -> EA
        - 12 -> Eb
        - 13 -> Ec
        - 14 -> Ed
        - 15 -> EE
        - 20 -> P0
        - 21 -> P1
        - 23 -> P3
        - 24 -> P4
        - 25 -> P5
        - 26 -> P6
        - 31 -> Pb
        - 33 -> Pd
        - 38 -> PP
        - 39 -> H0
        - 40 -> H1
        - 41 -> H2
        - 42 -> H3
        - 43 -> H4
        - 44 -> H5
        - 45 -> H6
        - 46 -> H7
        - 47 -> H8
        - 48 -> H9
        - 49 -> HA
        - 50 -> Hb
        - 52 -> Hd
        - 53 -> HE
        - 54 -> HF
        - 55 -> HH
        - 57 -> HP
        - 65 -> C7
        - 112 -> bH
        - 116 -> F1
        - 134 -> L0
        - 135 -> L1
        - 136 -> L2
        - 138 -> L4
        - 139 -> L5
        - 141 -> L7
        - 142 -> L8
        - 143 -> L9